 |
 |
 |
 |
|
 |
|
**Note: This model is stand alone only. It can not accommodate top fill or multi feed. Please see part number 0393-1A for top fill, multi feed option.
Soap Recommendation (See "A Note from the Manufacturer Section" for tested soaps)
Foam soap. Clear foaming liquid, no abrasives.
pH in range 7+/- 1.5
Viscosity Range mPas-cP: 1-100
ConstructionEZ Fill™ Vanity Mounted Automatic Soap Dispensing System Foam Soap Dispenser shall dispense liquid foaming soap with pH in range 7± 1.5 and viscosity in range 1–100 cP (mPas) and shall dispense in stream cycles with soap volume and air volume adjustable by owner with remote control programming unit (optional: Model Number: 0393-R). Operation is initiated by hands-free sensor controlled by microprocessor digital circuitry and peristaltic pump is powered by six (6) ‘D’-size 1.5V batteries (supplied by others) in a screw-locked IP67 rated compartment (provided) located under counter or an AC Adapter (also IP67 rated, provided, select model) plugged into GFCI outlet (by others). Unit shall have chrome plated spout and sensor housing with a highly polished finish (or Matte Black when code –41 is specified) over all exposed surfaces. Unit shall have LED in sensor to indicate function and battery condition (when Battery Box, 0390-BP {provided}, is used). A self-adhesive label shall be supplied for use at owner’s option to indicate dispenser function. Unit shall mount on vanity deck up to 2" thick through 1" minimum diameter hole to 1-1/4" maximum diameter hole and shall resist forced rotation up to 177 in-lbf (20 Nm) with 0390-ARK properly installed (provided).
NOTE: Soap supply shall be from Model Number: 0390 EZFill™ Vanity Mounted Top-Fill Port and Multi-Feed Tank (supplied separately) with capacity of 1.6 Gal (6 L) of liquid soap containing no abrasives or particulates. Up to six (6) individual EZFill™ vanity mounted automatic soap dispenser units shall draw from each Multi-Feed tank located under counter through connection with under-counter soap distribution tubing (provided). Owner’s Manual and Installation Guide (OM & IG) shall be provided with unit in carton.
Installation for both AC and Battery Operated
Install spout and sensor housing to vanity deck with anti-rotation kit escutcheon flange, rubber washers and basin nut (supplied) through 1-1/8" Diameter mounting hole and 5/32" Diameter adjacent hole for anti-rotation pin of escutcheon flange. Connect flex tubing from soap dispenser head to fitting on top of foam compressor. Connect com plug from dispenser head to com socket from foam compressor. Mount pump assembly with wall bracket to convenient structure under vanity within 24" of L-fitting on foam compressor bottom with two (2) screws and wall anchors (supplied). Connect flex tubing from L-fitting on air compressor to fitting on top of pump assembly. Connect com plug from foam compressor to com socket from pump assembly. Mount battery compartment in convenient location under vanity deck with two (2) screws and wall anchors (supplied) within easy reach of extension cable length and plug connector into mating inline power connector. Install six (6) ‘D’-size 1.5V cells (supplied by others) in under-deck battery compartment according to polarity indication, plug battery cable jack into battery box socket in cover handle and screw lock cover. Alternatively, plug AC Adapter into GFCI power outlet located under vanity within 13.5 ft (412 cm) of pump assembly and plug connector into mating inline power connector. Operation
Operation is initiated by hands-free sensor controlled by microprocessor digital circuitry and peristaltic pump is powered by an AC Adapter (also IP67 rated, provided, select model) plugged into GFCI outlet (by others) or an AC Adapter (also IP67 rated, provided, select model) plugged into GFCI outlet (by others).
To activate dispenser, place hand under spout near the sensor for approximately 1 second. Spout dispenses foam hand soap. Optional remote control unit p/n 0393-R allows owner programming of alternate dispense amounts. Unit will dispense soap while batteries are at suitable charge level, correct viscosity soap is present in the tank, and system is correctly maintained to enable dispensing (red LED is not flashing continuously - low battery or does not remain dark - no battery charge). There is a push button that releases soap for easy soap priming.
System allows filling soap from top of vanity without requiring removal of tank under vanity.
Warranty
Two (2) Years Manufacturer's Warranty - Warranted to be free of defects in material or workmanship for Two (2) years from date of sale.
Options Model 0394-1A Universal Stand Alone Model, Battery Operation, Bright Chrome Plated Finish
Model 0394-1A-41 Universal Stand Alone Model, Battery Operation, Matte Black Finish
Model 0394-1AC Universal Stand Alone Model, AC Adapter Operation, Bright Chrome Plated Finish
Model 0394-1AC-41 Universal Stand Alone Model, AC Adapter Operation, Matte Black Finish
Model 0393-1A Top Fill, Multi Feed Dispenser Head, Battery Operation, Bright Chrome Plated Finish
Model 0393-1A-41 Top Fill, Multi Feed Dispenser Head, Battery Operation, Matte Black Finish
Model 0393-1AC Top Fill, Multi Feed Dispenser Head, AC Adapter Operation, Bright Chrome Plated Finish
Model 0393-1AC-41 Top Fill, Multi Feed Dispenser Head, AC Adapter Operation, Matte Black Finish
Model 0390 is kit for multi-feed kit dispenser head option 0393-1A or 1AC. Includes 5 L container, Top Fill Tube, and Counter Fill Port with Cover
|
|
|
|
|
|
|