|
|
|
|
|
|
|
Construction L-shaped Phenolic Fold-up Shower Stall Seat shall have all metal parts of type 304 stainless steel alloy 18-8 with
satin finish. Seat frame and support legs shall be 1" diameter and 1-1/4" square x 18 gauge with
3/16" thick mounting flanges and 16 gauge guide bracket/arm support. Structural assembly shall be of
welded construction and all exposed edges and corners shall be eased and smoothed. Seat shall be solid phenolic
with white top and bottom surfaces and shall have black edges. Support arm shall fold up when in retracted position to provide low profile against wall. No extra fittings shall be required to retain seat in storage position. Guide
bracket shall control seat lowering into operating position and gas struts shall assist opening and lowering actions.
Seat shall be field reversible for RH or LH requirements. Unit shall satisfy 2010 ADA Accessibility Standards
when mounted properly.
ASI Shower Seats are designed to meet and exceed 2010 ADA Accessibility Standards and ANSI A117.1 specifications, that fabricated product shall be of adequate strength to support a load of 250 lbs (113,4 kg) and unit shall
conform to size and edge clearances as diagrammed. Mounting to the wall is a critical part of the system to meet
this requirement. To withstand the shear, tension or pullout, and torsion loads generated by the maximum loading,
the fastener system must be adequately sized. Unit is load rated to support a weight of 500 lbs (227 kg) at front
edge when properly installed and has been tested to successfully hold a weight in excess of 1000 lbs (454 kg).
Installation This unit is surface mounted. Installer/construction contractor must provide concealed anchor plate or blocking as
specified in construction documents or as required by local building codes prior to wall finishing. Fasten unit
flanges and guide bracket to concealed anchor or blocking plate with appropriate hardware. Ensure that all fastener systems are waterproofed for wet-wall installations. Note that concealed
mounting plates or anchors and hardware are not supplied with this product and must be specified separately. Ensure that mounting configuration complies with local building codes. Unit is reversible in the field for right or left
hand installation.
Warranty One (1) Year Manufacturer's Warranty - Warranted to be free of defects in material or workmanship for one (1) year from date of sale.
Operation Fold-up Shower Seat requires only one hand operation to manually lower to horizontal position for use or raise for
departure and arrival. Guide bracket with spring detent prevents seat from dropping and provides positive support
in usage position as well as spring locked storage position. Gas charged struts assist opening by allowing slowly
lowering seat to operating position from storage and assist closing by self-raising seat from approximately 25° to
85° and providing partial extra push required to achieve fully stored position.
Left Hand Options Model 8206-SC-L Left Hand, 33" W, Slow Closing Model 8206-L-28 Left Hand, 28" W Model 8206-L Left Hand, 33"
Right Hand Options Model 8206-SC-R Right Hand, 33" W, Slow Closing
|
|
|
|
|
|
Accessories |
ASI 8206-R-28 Right Hand L-Shaped Folding Shower Seat, Phenolic, 28" Wide
|
|
ASI 8206-L-28 Left Hand L-Shaped Folding Shower Seat, Phenolic, 28" Wide
|
|
ASI 8206-SC-L Slow Closing L-Shaped Fold Up Phenolic Shower Seat, Left Hand, 33" Wide
|
|
ASI 8206-R Right Hand L-Shaped Folding Shower Seat, Phenolic, 33" Wide
|
|
|
|
|
|
|
|
|
|
ASI 8206-SC-R Slow Closing L-Shaped Fold Up Phenolic Shower Seat, Right Hand, 33" Wide
|
|
ASI 8206-L Left Hand L-Shaped Folding Shower Seat, Phenolic, 33" Wide
|
|
|
|
|
|
|
|
|
|
|
|