|
Construction
Partition mounted toilet seat cover and multi roll toilet tissue dispenser with sanitary napkin disposal is fabricated of 18-8, type 304 stainless steel. The cabinet is an all welded construction and equipped with a plastic sight barrier panel for the seat cover dispenser. Flange is drawn and beveled, one piece, seamless construction. The doors are secured to the cabinet with full length piano hinges and are equipped with tumbler locks keyed like other Bobrick washroom accessories. Spindles are theft resistant, one piece, molded ABS. Disposal panels are secured to cabinet with spring loaded hinges resulting in the doors being in the closed position. Removable waste receptacle is fabricated of leak proof molded polyethylene with a 0.8 gallon capacity. All exposed surfaces are satin finish.
Installation
Mount unit in toilet partition 1/2'' to 3-7/8'' (13 x 98mm) thick, centered through a cutout specially ordered from partition
manufacturer or field cut. Dimensions of cutout are to be 15-1/2" wide x 28-7/8" high (395 x 735mm). Top of cutout should be
42-1/4" (1075mm) from finish face of floor to allow placement of horizontal grab bar at 33" (840mm) height across front of unit
and installation of 18" vertical grab bar (ICC A117.1-2017). For factory made cutouts, location and size details must be furnished
to partition manufacturer. For hollow core metal partitions, provide solid framing into which sheet metal mounting screws can
be secured.
For installation with sheet metal screws furnished, place unit firmly in partition cutout, making certain entire perimeter of
fixed flange is flush with and tight against partition surface. Install the unit so the side that has the fixed flange flush with face
of cabinet is in the accessible toilet compartment for use by individuals with disabilities. Secure to partition with sheet metal
screws through four mounting holes in fixed flange at points indicated by an S. On other side of partition, position adjustable
flange (which serves as an escutcheon) so mounting holes are not in line with mounting holes in fixed flange. Make certain
entire perimeter of adjustable flange is flush with and tight against partition surface before securing with sheet metal screws
furnished.
For through bolting method of installation, make sure mounting holes in adjustable flange are in line with holes in fixed flange.
Using adjustable flange as template to mark locations, drill 7/32" or 1/4" (5.5 or 6.4mm) holes through partition. Provide
four binder posts and #6 (3.5mm) flat-head screws to secure unit and its adjustable flange.
Note: Cutouts in Bobrick toilet partitions can be pre-cut for Bobrick partition mounted accessories at factory if location and size
of cutouts are specified and order for both partitions and accessories are received together.
Designer's Notes:
1. Partition-mounted B-3571 with one side flush to partition in accessible toilet compartment has toilet tissue dispenser on
left side of unit.
2. Position unit on panel with toilet tissue dispenser outlet 24" (610mm) minimum, 42" (1065mm) maximum from rear wall.
3. For unit to mount on left side of toilet (when seated on toilet) see model B-35715.
4. When combination units are mounted in an accessible toilet compartment through the shared toilet partition panel, the
units location in the adjoining toilet compartment must permit the units complete operation, and allow for the unit's door
to swing clear of the toilet when custodians service the unit.
5. For visual placement of models inside toilet compartment, click on the tab "A Note from the Manufacturer" next to the technical specs tab above.
Operation
Holds four (4) standard core toilet tissue rolls up to 5-1/4" diameter. Spindles can only be accessed when the door is open. Toilet seat cover dispenser holds 1000 single or half fold paper covers. The door unlocks with key provided and swing open for filling. The 0.8 gallon receptacle is removable for servicing.
Warranty
One (1) Year Manufacturer's Warranty - Warranted to be free of defects in material or workmanship for one (1) year from date of sale.
|