Bobrick B-9806x36 Inch Grab Bar - Division 10 Direct

Home > Grab Bars > Straight, 1-1/2" OD >

Bobrick Fino Collection B-9806x36 36" Straight Grab Bar 1-1/2" (38mm) OD - Satin Stainless

Bobrick B-9806x36" Stainless Steel Grab Bar image

List Price: $400.80

Our Price: $253.58

Savings: $147.22

Manufacturer: Bobrick
Country of Origin: United Kingdom
Availability: Usually Ships within 2-3 Business Days

Product Code: B-9806X36

Qty:

Description

Technical Specs

Bobrick Fino Collection B-9806x36 36" Straight Grab Bar 1-1/2" (38mm) OD - Satin Stainless

Construction
Grab Bar shall be stainless steel with satin finish. Grab bar shall have type-303, 14 gauge stainless steel tubing. Tubing is 1-1/2" outside diameter. Clearance between the grab bar and the wall shall be 1-1/2". Concealed mounting flanges shall be 5-16" thick, threaded solid stainless steel with satin finish, 2" diameter, equipped with three screw holes for attachment to wall. Flange covers shall be 1/8" thick, threaded solid stainless steel with satin finish, 2" diameter and shall conceal the mounting screws. Threaded solid support posts shall have 1/4" wall thickness, 1" outer diameter securing the flange covers. A metric M8 hex screw, with a curved washer shall connect the grab bar's tube with the flange. Grab bar shall comply with accessible design (including ADAAG in the USA) for structural strength.

*Grab bars are no stronger than the anchors and walls to which they are attached and must be firmly secured in order to support the loads for which they are intended. To avoid potential injury, the building owner or maintenance personnel should remove the grab bar from service if the grab bar is not adequately secured to wall.

Installation
Provide concealed anchor device or backing as specified or required in accordance with local building codes before wall is finished. Fasten mounting flanges to anchor device or backing. Put flange covers over each mounting flange to conceal mounting screws. Concealed anchor devices and mounting screws are not included with Bobrick grab bars and must be specified as an accessory.

Place flanges in desired mounting locations. Use flange as a template to mark location of mounting screws and drive mounting screws into the wall at marked locations. Install grab bar on the wall by placing the flange covers onto the flange followed by the support posts, placed onto the flange covers. Place M8 hex screw with curved washer through the tube's elongate screw holes into the flange and tighten the screw. Eventually snap the two end-covers onto each of the tube's end.

Note: Recommend use of #10 sheet metal screws or wood screws to install flange

Mounting Kits:

Dry Wall Mounting Kit- Bobrick offers a mounting kit that allows the FINO-grab bars to be installed in dry walls without backing. Wall requires minimum 5/8" painted or tiled dry wall. Mounting Kit No. 9806-20

Glass Mounting Kit- Bobrick offers a mounting kit for Glass-partitions (other material is possible as well) for securing the grab bar from the opposite side of the panel via a "through-fix." Panel thickness can range from 1/2" to 1-3/8". Mounting Kit No. 9806-21

"Back to Back" Mounting Kit- Bobrick offers a kit for the installation of two grab bars against each other, being on the opposite side of the panel. Panel thickness can range from 1/2" to 1-3/8". Mounting Kit No. 9806-22.

Warranty
One (1) Year Manufacturer's Warranty - Warranted to be free of defects in material or workmanship under normal usage service for one (1) year from date of sale.

Additional Options
Custom Grab Bar configurations and sizes are available.

Call us at 920-569-0895 ext. 2 or email [email protected] for pricing and lead times.